Engineering solutions in the field of
lubricants and sealants


Buy

Description

Air-curing dry lubricant.



Operating temperatures

-70°C +250°C

Pre-packing

5kg
  • Applications
  • Friction units
  • Advantages
  • Problems to be solved with this material
  • The combination of materials
  • Features

Applications

FEATURES

• Air drying
• Avoidance of stick-slip
• High ageing resistance


APPLICATIONS

• For metal/metal combinations with slow to medium fast movements and high loads.
• Suitable for the permanent lubrication of highly stressed sliding guides with low sliding speeds, oscillating movements or intermittent operation.
• Improving the running-in process and for lubrication under high vacuum and at extreme temperatures.
• Used successfully for cylinder-head bolts, toaster guides, car mirror adjustment
mechanisms, high voltage switches, for the running-in of highly stressed gear
wheel.
• Emergency lubricant for parts of the rotor head of wind energy installations and for groove-free cold extrusion of steel.

It is used in friction

  • Sliding bearings
  • Sliding guideways
  • Enclosed gears
  • Open gears
  • Threaded connections
  • Strips

Advantages

  • Cold resistance
  • Termal (heat) resistance
  • Chemical resistance
  • Working capacity in vacuum
  • Working capacity in moisture
  • Working capacity in dust
  • Radiation resistance
  • Good anticorrosion properties (good corrosion protection)
  • Good adhesion strength
  • Good water washout resistance
  • Good fretting corrosion protection
  • Emergency properties
  • Can be painted over
  • Avoidance of stick-slip
  • Provides constant torque for threaded connections
  • Easy mounting / dismounting

Problems to be solved with this material

  • Seizure
  • Stick-slip motion
  • Fretting corrosion
  • Dust sticking onto lubricating surfaces
  • Dust intrusion into lubricating points and abrasive wear
  • Corrosion
  • Lubricant wash-out
  • Lubricant destruction of chemically active medium exposure
  • Lubricant efficiency loss in vacuum
  • Lubricants leaking off or emission due to centrifugal forces
  • Frequent re-lubrication
  • Difficult mounting / dismounting
  • Unstable torque because of wide range friction coefficient
  • Liquid and consistent lubricants application failure

Material combination in friction pair

  • Metal - Metal
Стандарт Показатель Ед. изм. Значение
ЦветТемно-серый
Антифрикционные добавки (наполнители)Твердые смазочные материалы: дисульфид молибдена - 16%, графит - 4,9%
Прочие составляющиеОрганический связующий агент (эпоксидная смола), вода
CTM 0242 IСодержание нелетучего остатка%38
Диапазон рабочих температур°Сот -70 от +250
DIN 53 211/4Условная вязкость при 20 °С (тигль DIN4)с21
Температура вспышки°C84
DIN 53 217/2Плотность при 20 °Сг/см31,2
CTM 0007 ApH при 20 °С9
Срок годности при хранениилет1
ASTM D 2625Критическая нагрузка (метод Falex) для поверхности без предварительной обработки / после фосфатирования / после пескоструйной обработкикH-/-/11,3
ASTM D 2714Срок службы (испытание на машине LFW-1 при вращательном движении до коэффициента трения f=0,1 при нагрузке N=2860 H, частоте вращения n=72 об/мин, скорости скольжения v=7,9 м/мин) для поверхности без предварительной обработки / после фосфатирования / после пескоструйной обработкитыс. оборотов-/29/-
ASTM D 2714Срок службы (испытание на машине LFW-1 при возвратно-поступательном движении до коэффициента трения f=0,08 при нагрузке N=900 H, частоте w=89,5 циклов/мин) для поверхности без предварительной обработки / после фосфатирования / после пескоструйной обработкитыс. циклов-/89/-
Условия отверждения (выдержка/температура)мин/°С60/200

		

		
		
		
		
Яндекс.Метрика