description

Extreme-pressure lubricant for assembly, press fitting, threaded connections, running-in and maintenance.

Applications –

FEATURES

Excellent protection against fretting wear and corrosion
Extends service life
Low friction
Lubricate beyond the yield point of most metals in boundary applications, reducing wear and helping to prevent seizing, galling and excessive friction
Aid run-in and reduce frictional force and surface damage
Low coefficient of friction allows for effective conversion of torquing force into holding force;
reduces the force required for disassembly of threaded fasteners

APPLICATIONS

Molykote G-n Metal Assembly Paste lubricates surfaces subjected to extreme pressures. Specific applications include:

Running-in lubricant – for new or rebuilt equipment, such as gears, splines,
journal bearings, cams and ways
Metalworking – helps prevent galling, welding and metal pickup on tools and
dies in machining, stamping, and drawing operations, tube bending, thread
rolling, cold heading, swaging and forging
Assembly lubricant – reduces torque in tightening threaded fasteners and tension variation from bolt to bolt; eases disassembly and reduces chance of damage
Helps prevent fretting wear and corrosion, and cold welding of bearing shafts, bushings and splines
Press-fitting lubricant – allows press fitting without chatter or stick-slip in most cases; reduces the force required for interference fitting and minimizes distortion

Molykote G-n Metal Assembly Spray is primarily designed as a running-in lubricant for plain bearings, splines, gears, cams and ways, and because of its low coefficient of friction, as a lubricant for movable screws, threaded spindles and lead screws. It can also be used wherever protection against friction and high load conditions is needed, where burnishing is impractical, or where a paste in aerosol form is desired. It is suitable for airframe and aircraft engine applications.

It is used in friction

  • Sliding bearings
  • Sliding guideways
  • Chains
  • Linear bearings
  • Enclosed gears
  • Open gears
  • Piston-cylinder-group (unit)
  • Interference fits
  • Threaded connections
  • Strips
  • Spline / key joints

Advantages

  • Termal (heat) resistance
  • Higher load carrying capacity
  • Working capacity in moisture
  • Good anticorrosion properties (good corrosion protection)
  • Good fretting corrosion protection
  • Emergency properties
  • Excellent wear protection
  • Avoidance of stick-slip
  • Provides constant torque for threaded connections
  • Reduces friction and tool wear in metal cutting
  • Easy mounting / dismounting

Problems to be Solved material

  • Higher heating and wear of cutting tools
  • Seizure
  • Stick-slip motion
  • Brinelling or false brinelling
  • Fretting corrosion
  • Corrosion
  • Frequent re-lubrication
  • Difficult mounting / dismounting
  • Unstable torque because of wide range friction coefficient

Recommended by manufacturers

  • AirTech Vacuum
  • Atlas Copco
  • BRP-Rotax GmbH
  • Fenner Drives
  • IMA
  • Ingersoll Rand
  • Innovative Hydraulic Designs
  • Magnadrive
  • Milwaukee Electric Tool
  • Naval sea systems command
  • Prime Measurement Products
  • Ringfeder
  • SPX
  • Swagelok
  • Tetra Pak
  • Uponor
  • Vetus

The combination of materials friction pair

  • Metal - Metal

FEATURES

Стандарт
Показатель
Ед. изм.
Значение
Цвет
Черный
Базовое масло
Минеральное
Загуститель
Загуститель
Антифрикционные добавки (наполнители)
Твердые смазочные материалы: графит, дисульфид молибдена
Верхний предел рабочих температур твердых смазочных материалов, входящих в состав продукта
°С
+450 (при ограниченном доступе воздуха +630)
DIN ISO 2137
Пенетрация неперемешанной смазки
мм/10
280-310
ISO 2811
Плотность при 20 °С
г/см3
1,35
DIN 51 807 pt.1
Водостойкость (3 ч, 90 °C)
ст. эмульгирования
2
DIN 51 350 pt.4
Нагрузка сваривания (испытание на четырехшариковой машине трения, 1450 об/мин/10 с),
Н
2800
Критическая нагрузка (метод Almen-Weiland)
Н
>20000
DIN 51 350 pt.5
Показатель износа (испытание на четырехшариковой машине трения, 1450 об/мин/800 Н/1 ч)
мм
0,75
Сила трения при критической нагрузке (метод Almen-Weiland)
Н
2600
Коэффициент трения в болтовом соединении (М12, материал 8.8) для головки болта/для резьбы
0,06/0,12
Коэффициент трения для посадки с натягом
0,08 (без изменения)