Engineering solutions in the field of
lubricants and sealants


Buy

Description

Silicone grease with solid lubricants.



Operating temperatures

-50°C +180°C

Pre-packing

100g1kg5kg25kg180kg
  • Applications
  • Friction units
  • Advantages
  • Problems to be solved with this material
  • Recommended by manufacturers
  • The combination of materials
  • Features

Applications

FEATURES

Good compatibility with plastics and rubber
Wide operating temperature range(-50° to 180°C)
Silicone based grease

APPLICATIONS

Especially suited for the low friction operation of most rubber or plastic parts such as:
Bearing bushings, gears and chains
Sealing rings, sliding tracks and switches
Which are typically found in:
Bowden cable control systems
Electric motors and gearboxes
Household and garden appliances
Automotive brake systems
Automotive clutch systems

It is used in friction

  • Sliding bearings
  • Sliding guideways
  • Enclosed gears
  • Open gears
  • Cased control cables
  • Gaskets

Advantages

  • Cold resistance
  • Termal (heat) resistance
  • Working capacity in moisture
  • Working capacity in dust
  • Good anticorrosion properties (good corrosion protection)
  • Good water washout resistance
  • Good shear stability at low temperatures
  • Emergency properties
  • Compatible with many plastics
  • Compatible with many elastomers
  • Avoidance of stick-slip

Problems to be solved with this material

  • Stick-slip motion
  • Dust intrusion into lubricating points and abrasive wear
  • Corrosion
  • Lubricant wash-out
  • Frequent re-lubrication
  • Plastic and elastomer details deformation and destruction

Recommended by manufacturers

  • BRP-Rotax GmbH

Material combination in friction pair

  • Metal - Plastic
  • Metal - Elastomer
  • Plastic - Plastic
  • Plastic - Elastomer
Стандарт Показатель Ед. изм. Значение
ЦветБелый
Базовое маслоСиликоновое
ЗагустительЗагуститель на базе литиевого комплекса
Антифрикционные добавки (наполнители)Политетрафторэтилен (ПТФЭ)
ПрисадкиПротивозадирная
Диапазон рабочих температур°Сот -50 до +180
DIN 51 562Кинематическая вязкость базового масла при 25 °Смм2/c200
DIN ISO 2137Пенетрация перемешанной смазки (60 циклов)мм/10245-275
DIN 51 818Класс консистенции по NLGI2...3
DIN ISO 2176Температура каплепадения°C>250
ISO 2811Плотность при 20 °Сг/см31,02
DIN 51 808Стойкость к окислениюкПа10
DIN 51 802Степень коррозии по методу Emcor (подшипники качения, дистиллированная вода)0-1
Коэффициент трения (трение стального шарика диаметром 12,7 мм о пластиковую поверхность при нагрузке 6,3 Н и скорости скольжения 10 мм/с в течение 24 ч)<0,04
DIN 51 805Давление истечения при -50 °Сбар<0,8
ASTM D 1478-80Момент сопротивления вращению подшипника качения при пониженной температуре -50 °С при запуске / через 20 мин после запуска / в рабочем режимеH*м<0,120/<0,090/-

		

		
		
		
		
Яндекс.Метрика